- 您现在的位置：买卖IC网 > Sheet目录317 > C8051F380-TB (Silicon Laboratories Inc)DEV KIT FOR C8051F38X
C8051F380/1/2/3/4/5/6/7/C
21.6. Function Addressing
The FADDR register holds the current USB0 function address. Software should write the host-assigned 7-
bit function address to the FADDR register when received as part of a SET_ADDRESS command. A new
address written to FADDR will not take effect (USB0 will not respond to the new address) until the end of
the current transfer (typically following the status phase of the SET_ADDRESS command transfer). The
UPDATE bit (FADDR.7) is set to 1 by hardware when software writes a new address to the FADDR regis-
ter. Hardware clears the UPDATE bit when the new address takes effect as described above.
USB Register Definition 21.7. FADDR: USB0 Function Address
Bit
7
6
5
4
3
2
1
0
Name
Type
UPDATE
R
FADDR[6:0]
R/W
Reset
0
0
0
0
0
0
0
0
USB Register Address = 0x00
Bit Name
Function
7
UPDATE
Function Address Update Bit.
Set to 1 when software writes the FADDR register. USB0 clears this bit to 0 when the
new address takes effect.
0: The last address written to FADDR is in effect.
1: The last address written to FADDR is not yet in effect.
6:0 FADDR[6:0] Function Address Bits.
Holds the 7-bit function address for USB0. This address should be written by software
when the SET_ADDRESS standard device request is received on Endpoint0. The
new address takes effect when the device request completes.
21.7. Function Configuration and Control
The USB register POWER (USB Register Definition 21.8) is used to configure and control USB0 at the
device level (enable/disable, Reset/Suspend/Resume handling, etc.).
USB Reset: The USBRST bit (POWER.3) is set to 1 by hardware when Reset signaling is detected on the
bus. Upon this detection, the following occur:
1. The USB0 Address is reset (FADDR = 0x00).
2. Endpoint FIFOs are flushed.
3. Control/status registers are reset to 0x00 (E0CSR, EINCSRL, EINCSRH, EOUTCSRL, EOUTCSRH).
4. USB register INDEX is reset to 0x00.
5. All USB interrupts (excluding the Suspend interrupt) are enabled and their corresponding flags cleared.
6. A USB Reset interrupt is generated if enabled.
Writing a 1 to the USBRST bit will generate an asynchronous USB0 reset. All USB registers are reset to
their default values following this asynchronous reset.
Suspend Mode: With Suspend Detection enabled (SUSEN = 1), USB0 will enter Suspend Mode when
Suspend signaling is detected on the bus. An interrupt will be generated if enabled (SUSINTE = 1). The
Rev. 1.4
183
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
C8051F912DK
KIT DEV FOR C8051F91X/C8051F90X
C8051F930-TB
BOARD TARGET/PROTO W/C8051F930
C8051T610DB24
DAUGHTER BOARD T610 24QFN SOCKET
C8051T630DB20
BOARD SOCKET DAUGHTER 20-QFN
CAN-100
BOARD EVAL RS232 100QFP
CANADAPT28
KIT ADAPTER CANDEMOBOARD 28PLCC
CAT24AA01WI-GT3
IC EEPROM SERIAL 1KB I2C 8SOIC
CAT24AA02WI-G
IC EEPROM SERIAL 2KB I2C 8SOIC
相关代理商/技术参数
C8051F381
制造商:SILABS 制造商全称:SILABS 功能描述:USB DRIVER CUSTOMIZATION
C8051F381-GM
功能描述:8位微控制器 -MCU USB-64K-Flash
RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F381-GMR
功能描述:8位微控制器 -MCU USB-Flash-64k-ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F381-GQ
功能描述:8位微控制器 -MCU USB-64K-Flash
RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F381-GQR
功能描述:8位微控制器 -MCU USB-Flash-64k-ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F382
制造商:SILABS 制造商全称:SILABS 功能描述:USB DRIVER CUSTOMIZATION
C8051F382-GQ
功能描述:8位微控制器 -MCU USB-Flash-32k-ADC
RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F382-GQR
功能描述:8位微控制器 -MCU USB-Flash-32k-ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT